Bits of the Past (Dropcheck)

Type
Vendor
Category
Open-hardware designer
Manufacturer
Dropcheck (Lenore Underwood), BitsofthePast.com
Green replacement XF551 disk-drive circuit board with large capacitors, the drive controller chips in sockets and a grey ribbon cable attached, on a workbench

Overview

BitsofthePast.com is the project site of Dropcheck (Lenore Underwood), an AtariAge regular known for re-creating old Atari add-on boards and repairing the weak spots of original hardware. Like AtariBits, with which it has shared projects, it describes itself as a development site only. The designs are experimental, specifications may change, and everything is released to the public domain with a request for credit if you modify or sell a design. Each project page offers schematics, BOMs, Gerbers and, where needed, firmware. Donations are welcome but optional. The site notes that the 14xx-series replica boards alone cost over $2,000 to develop.

Dropcheck has also sold built boards at times. MyTek recalls her RAMBO XL clone being sold from the site for a short period.

Projects (as of November 2026)

Area Boards
XF551 a reimaged XF551 controller (2014 in its first form): a proper double-sided board replacing Atari's single-sided original, whose fragile traces often caused SIO faults. It adds optional dual-BIOS selection, a front-panel drive-ID switch, a reset button and a two-digit LED track display. A second version needs fewer parts salvaged from the donor drive. There are also an alternative 8.333 MHz oscillator board, since the original oscillator is now almost impossible to find, and front-panel accessory boards
SF551 the whole XF551 circuit squeezed into an Atari SF314 (ST-style) case with a 3.5-inch mechanism, plus a control board for the track display and switches. The page calls it neither easy nor cheap, and it needs solid SMD skills
Internal XL/XE boards Super MMU (a plug-in fix for early Ultimate 1MB v1.0 boards, whose main chip could be damaged by some cartridges driving RD4/RD5), a 4-in-1 OS switch (four 16K images in a 27C512), UltraOS+ 3-in-1 (re-created with Mytek, functionally equal to Bob Puff's original: Ultra Speed Plus, XL-Fix Plus and stock OS), Rambo256 (a reimaged ICD RAMBO XL), Ramrod XL/XE (a reimaged version of the ICD/Newell multi-OS system, choosing among up to three 27C128 OS images such as OS/N XL, Omnimon XL and Omniview XL; see Ramrod) and an internal Supra/ICD parallel printer adapter (needs a 27C64 burned with its firmware)
Cartridge boards cartridge extenders (including one that lets more cartridges fit a 1200XL), a breakout board, a two-cartridge switch (GAL logic by tf_hh), an 800XL cartridge-guide extension for up to 12 inches of cable, and XE Super Cart boards for 128K Super XE-style banked games such as Midi-Maze
PBI/ECI boards PBI and ECI breakouts, right-angle 130XE cartridge/ECI extensions, and an XE ECI to XL PBI adapter that lets most 800XL PBI devices run on a 130XE, with a few internal wires for CASINH and RDY
Replicas a 1450XL replica motherboard of the pre-production machine (v1.4a), with the 1400XL SALT test and speech-terminal cartridges. There are also 1250XL and 850XL remix boards

Tips

  • Read the tips documents. Most projects have assembly and troubleshooting notes. For the XF551 boards, take the 8040/8050 microcontroller, the WD1772PH controller and the oscillator from a known-good drive.
  • Skill levels vary a lot. A PBI breakout is easy. The SF551 and 1450XL are expert builds. Dropcheck says to build the 1450XL only if you are serious about finishing it: there's no case to fit it and the parts are expensive.
  • The XE-to-XL PBI adapter works with most, not all, PBI devices. Check the forum threads for the device you want.
  • For a list of current shops, see where to buy Atari 8-bit hardware.

Credits