400/800 RAM Upgrades You Can Build
- Year
- 1982
- Type
- DIY project
- Category
- Internal memory upgrade
- Manufacturer
- Homebrew designs (Steve Olsson; Claus Buchholz; Jay Torres & Jerry Rombert / WindHover Project)
Overview
The Atari 400 and 800 keep their RAM on plug-in memory boards. The 800 has three RAM slots, filled front to back with 8 KB or 16 KB boards up to 48 KB. The 400 has a single internal slot, and Atari only sold it with 8 KB or 16 KB. Commercial 32K and 48K boards from Axlon, Mosaic, Intec, Microtek and others filled the gap, but in the early 1980s they cost real money. Hobbyists worked out that Atari's own boards could be upgraded with cheap chips and a soldering iron.
Project 1: 8K boards to 16K (Atari 800)
Steve Olsson's "New RAMs for Old", collected in The Creative Atari, starts from a nice piece of semiconductor history. Atari's 8K boards use 4108 DRAMs, which are 16K × 1 4116 chips with one bad half, sorted and sold as 8K parts (4108-A has the lower half good, 4108-B the upper half). The 8K board is otherwise almost identical to the 16K one, so you swap in eight good 4116s and change a few jumpers.
Steps, in brief:
- Buy eight 4116s (200 ns or faster) per board from a reputable supplier.
- Open the module (two screws and a metal cover) and lift out the board.
- On the edge connector (1–22 on the front, A–Z on the back, with G, I, O and Q skipped), cut the small etches U–T, S–R, N–P and the etch from W to Z501 pin 15.
- Wire Z501 pin 15 to U, T to S, P to R, M to N.
- On the front, fit jumper C only and remove the others. On the back, run a fine wire from connector H to jumper D.
- Replace the eight chips at C503–C517 with the 4116s and reassemble. The whole job takes about 30 minutes.
Testing: PRINT FRE(0) should rise. Fill a GRAPHICS 8 screen white and look for holes, then run Olsson's POKE/PEEK loop, which writes 255 through memory and reports any ERR- addresses. Put a known-good board in slot 1 so that the board under test can be checked in full. The first 5K of the lowest board can't be tested this way.
Project 2: the 400 to 48K and 64K ("SuperRam")
Claus Buchholz published "A 48K Upgrade for Your 400" in the MACE (Michigan Atari Computer Enthusiasts) newsletter in September 1982, and it became known as the "MACE Mod". Jay Torres and Jerry Rombert of the WindHover Project wrote it up as the WindHover Atari 400 SuperRam Modification. They claim to have done the work first, and they deny permission to reprint it to MACE. Their notes put the cost under $25, against $95–170 for a commercial expander.
Parts: eight 4164 DRAMs (200 ns or faster), a 74LS158, 74LS02, 74LS74, 74LS00, and two 680 Ω resistors.
Outline of the 37-step procedure:
- Strip the 400 down to the motherboard and remove the RAM board.
- Power changes: 64K chips run from +5 V only. Cut the +12 V and −5 V feeds (edge pins X and Y to C521/C523), remove those capacitors and the per-chip bypass caps, and bridge +5 V into the old 12 V trace. Then swap in the 4164s, with pin 1 the right way round. At this point the board should still work as a 16K board, which makes a good checkpoint.
- Addressing: piggy-back a 74LS158 on the chip at Z503 and wire it to edge pins M and U and the old 5 V bus. Then, on the motherboard, cut two traces at Z103 and add a 74LS02 "dead bug" style wired to the cartridge-slot select lines and the memory slot. Two 680 Ω pull-downs go on cartridge pins A and 14.
- Power up. If the blue screen doesn't appear at once, switch off immediately and recheck.
The result is a 48K 400 that boots everything, because software that checks for more than 48K never sees the extra RAM. The optional 64K stage adds the 74LS00 and 74LS74 as a latch that bank-switches the extra 16K in place of the middle 16K of the 48K. WindHover supplied a DOS that used it as a 100-sector RAM disk with an instant DUP.SYS and MEM.SAV (DOS 2.5 could use it too). Torres also documented 96K, 160K and 288K upgrades for the 800.
Tips
- These projects involve cutting traces on 40-year-old boards. Photograph everything first and work slowly.
- Old DRAMs fail. Test every chip, and if possible keep sockets so you can swap them.
- Modern replacements avoid soldering altogether. 5cfab's 2022 SRAM boards (a 48K board for the 400 and a middle-slot 48K board for the 800) are drop-in.
- Antic's "Atari Brain Transplants" survey (November 1988) is a good overview of the many public-domain designs. The author built two Byrd-style 256K upgrades for the 800 without problems, and he warns that some homebrew designs lose data because of weak refresh circuits.
Credits
- Picture: An Atari 16K RAM board for the 800: the kind of board these upgrades modify. — Evan-Amos, Wikimedia Commons (Public domain)
- Steve Olsson — New RAMS for Old (The Creative Atari) — Steve Olsson; AtariArchives.org
- Jay Torres and Jerry Rombert — The WindHover Atari 400 SuperRam Modification (Nir Dary collection) — Nir Dary collection
- comp.sys.atari.8bit FAQ, section 6.12 (Michael Current, Feb 2026) — Michael Current (comp.sys.atari.8bit FAQ), 2026
- Lee Brilliant — Dr. Brilliant's Incredible Atari Brain Transplants, Antic v7n7 (Nov 1988) — AtariMagazines.com (Kevin Savetz), 1988
