Atari Silencer and 400 Full-Stroke Keyboard (Creative Atari mods)
- Year
- 1983
- Type
- DIY project
- Category
- Console modifications (400/800)
- Manufacturer
- Homebrew (John Anderson; Robert Noskowicz)
Overview
The Creative Atari (Creative Computing, 1983) collected hardware articles from Creative Computing magazine. Two of them fix the most common complaints about the first-generation machines: the internal speaker's beeps and keyclicks, and the Atari 400's flat membrane keyboard. One mod is trivially reversible. The other needs a soldering iron and some patience with an ohmmeter.
The Atari Silencer (John Anderson)
Besides sending sound to the TV, the Atari has a small internal speaker, like the Apple II. It sounds prompt tones, the 410 cassette's "record" and "play" signals and the keyboard "chirp". Anderson's machine was an 800. Anderson found it intrusive during late-night editing. The Atari Word Processor and a hi-res adventure that kept "blatting" for RETURN were the last straw. He wanted to switch it off without cutting wires or drilling, so a service technician would never know.
Parts (1983 Radio Shack): a pack of two-prong connectors (274-342), a micro-miniature SPST toggle switch (275-624), about two feet of bell wire, solder and tape.
How it goes together:
- Cut two 10-inch wires, and cut one of them into two 5-inch pieces. Twist the short pieces onto the long one and solder on two socket connectors and the switch, so the switch sits in series with the speaker. The plug halves aren't used.
- Turn the 800 over onto something soft, remove the five screws and lift the bottom panel off, easing it past the controller ports.
- Unplug the tiny speaker and remove it. With a toothpick, press down the tongue on each contact of the original speaker connector and slide the contacts out of their housing.
- Mount the switch in the left-hand vent slot of the bottom panel. Spread two slats gently with a screwdriver, push the switch neck through, and fit the washer and nut.
- Press the speaker contacts into the middle connector, refit the speaker, plug the far socket onto the speaker leads, and tuck the wire under the keyboard post away from the boards. Tape the original connector to the wire so you can restore it.
- Test with the keyboard repeat in Memo Pad mode.
The whole thing comes out in under five minutes if the machine ever needs service.
A standard keyboard for the 400 (Robert Noskowicz)
Noskowicz bought a 400 rather than an 800, because he reasoned that the extra memory access, second cartridge slot and better keyboard weren't worth about $400 more. After six months the flat keyboard drove him to "total exasperation". Atari offered no keyboard schematics, so he worked out the matrix with an ohmmeter. The 400's keyboard is just 61 momentary switches on a 22-conductor ribbon cable, and the scanning is done inside the computer. His Figure 1 maps each key to its pair of cable pins.
What he used: a 62-key "bare" keyboard (not mounted on a PCB) bought by mail order from California, about seven feet of ribbon cable, a 25-pin RS-232-style ribbon connector so the keyboard could be unplugged (22 wires are enough without one), and a small plastic tool box cut to shape as a case.
The build:
- Wire the new keyboard to match the Atari's matrix. Keys can sit in different places as long as the wiring follows the matrix.
- Stop the new keyboard's Caps Lock key from latching, because the Atari's CAPS key is momentary.
- He used the spare key to put two keys in series for SYSTEM RESET, so it couldn't be pressed by accident.
- Solder the new ribbon cable onto the back of the Atari keyboard where the original cable joins it, leaving the original in place, and mount the connector in the side of the case.
Because the two keyboards are wired in parallel, either one works. Noskowicz kept the new one on his lap, away from the computer, at his wife's suggestion.
Tips today
- A modern alternative for a better keyboard is a PS/2 interface such as the TransKey-II, which piggy-backs on POKEY instead of tapping the keyboard cable.
- See the Atari 400 and Atari 800 entries for the machines themselves.
Credits
- Picture: Anderson's Silencer drawings: where the switch goes in the bottom panel, and how the adapter lead sits between speaker and chassis. — Figures 3 and 4 of John Anderson's 'Atari Silencer', The Creative Atari (Creative Computing Press, 1983), from a scan of the book
- John Anderson — Atari Silencer, in The Creative Atari (atariarchives.org) — Figures 3 and 4 of John Anderson's 'Atari Silencer', The Creative Atari (Creative Computing Press, 1983), from a scan of the book
- Robert Noskowicz — Standard Keyboard for the Atari 400, in The Creative Atari (atariarchives.org) — Robert Noskowicz; AtariArchives.org
- comp.sys.atari.8bit FAQ, section 1.15 (keyboard connector: K0-K5 scan, KR1/KR2 response) — Michael Current (comp.sys.atari.8bit FAQ)
