600XL to 64K: The DIY Upgrade

Year
1988
Type
DIY project
Category
Internal memory upgrade
Manufacturer
Homebrew (design by Don Neff, MACE/WAUG)
Rear view of a beige Atari 600XL showing its expansion connector, ports and power switch

Overview

The Atari 600XL shipped with only 16 KB of RAM. That was enough for cartridges and BASIC, but far short of the 64 KB that most XL software, DOS 2.5 RAM disks and later demos expect. Atari's own fix was the 1064 Memory Module, a box on the parallel bus that brought the machine to 64 KB (62 KB usable). Third parties sold 32K, 48K and 64K expanders, and a few 600XLs were even sold in Canada with a 64 KB daughterboard by BOT Engineering already fitted.

The cheapest route, though, has always been to do it inside the computer. The 600XL's motherboard is laid out much like the 800XL's, and it only needs the bigger RAM chips and a little rewiring of the address multiplexers. The best-known recipe is Don Neff's "64K Upgrade for 600XL", published in the February 1988 Michigan Atari Magazine (MACE/WAUG). Several other hobbyist and kit versions appeared between 1986 and 1988, including Ken Sumrall's 1987 project and kits from Computer Service Land, Computer Support and York Computer Centre.

What you need

Item Notes
2 × 41464 DRAM (64K × 4, -10 = 100 ns) replace the two 16K DRAMs
Hook-up wire four short jumpers
Fine soldering iron, desoldering tool the board's fine traces run on the top side
Optional: two 18-pin sockets strongly recommended

The procedure

With the cartridge port at the back of the board:

  1. Replace the RAM. Remove the two 16K DRAMs at U11 and U12 and fit two 41464 chips, notches to the left. If the originals are soldered in, desolder them carefully: the fine traces are on top. On the new chip in U11 (next to the 74LS51), bend pin 8 up, out of the socket.
  2. Add the RAM jumper. Unsolder and lift one lead of the nearby resistor/jumper R36, then run a wire from the lifted pin 8 to that resistor lead. Taping the resistor helps keep it clear.
  3. Re-route the address multiplexers. On the two 74LS158 chips, bend up pin 3 on U5 and pin 10 on U6. Then connect them, plus the pads they came from, to the solder pads near U9 with two more jumpers, as shown in Neff's diagram.
  4. Test before you close up. Power on and type PRINT FRE(0). A successful conversion reports roughly 37 KB free to BASIC, because BASIC itself and the OS take the rest. Then reassemble.

Neff's own warning comes first in his notes: this is the upgrade "in its simplest form". If you don't understand it, don't do it, and you assume all risk. He reported using it several times without trouble.

How it works

A 41464 is organised 64K × 4, so two of them make a full byte-wide 64 KB, where the original 16K design used two 16K × 4 parts. Larger chips need one more multiplexed address line, which is what the extra jumpers to the 74LS158 address multiplexers supply. The MMU and PIA already handle the XL memory map, so once the RAM is there the machine behaves like an 800XL. It has 64 KB with RAM under the OS ROM, selected through PORTB bit 0 as on every XL.

After the upgrade

  • DOS 2.5, MyDOS and SpartaDOS will see the extra memory. Software that refused a 16K 600XL, including many disk-based games, will now load.
  • The machine is now a good base for a further 128K (130XE-style) upgrade. Those need 64 KB first.
  • Modern alternatives (2014 onward) replace the DRAM with static RAM modules for 600XL/800XL/65XE/800XE: tOri's Static RAM project, Lotharek's SRAM Module 64KB (2019, revised 2020–21) and a 2022 PBI SRAM card by 5cfab. If your DRAMs are failing, these sidestep refresh problems altogether.

Pitfalls

  • 600XL boards are cramped, and lifting traces is easy. Use low heat and desoldering braid.
  • Double-check pin 1 orientation. A reversed DRAM can die instantly.
  • If FRE(0) still shows a 16K figure, recheck the multiplexer jumpers. A black screen usually means a pin-8 or R36 mistake.

Credits