Archiving Your Own Atari Disks, Tapes and Cartridges

Somewhere there is a box of Atari disks, tapes or cartridges: your own programs from 1985, a user group's library, a game nobody else seems to have. Magnetic media doesn't last for ever, and every year a few things that were never archived still turn up. This guide is about getting them into image files properly, choosing the right method for each item, and recording what you have.

It ties together the detailed guides on this site. For what the image formats contain, see Atari 8-bit File Formats Explained; for protected disks, Copy Protection and ATX Disk Images; for cassettes, Loading and Saving Atari Cassettes.

1. Before you start

  • Protect the originals. Make sure every original disk is write-protected (a tab over the notch of a 5.25" disk) before it goes near a drive, and never "test" an original in a drive you aren't sure of.
  • Clean and check the drive first. A dirty head or a drive running at the wrong speed gives bad reads and can damage fragile disks. See Caring for Atari 8-bit Hardware and Atari 1050 Disk Drive: Checking and Adjusting Speed.
  • Start with what you can replace. Test your set-up on a common disk before you touch the rare one.
  • Photograph and note everything: the label, sleeve and box, handwritten notes, and which side of a flippy disk you read. That context is half the value of an archive.

2. Disks: four routes

Pick the route by what the disk is and what equipment you have.

Route A: a real Atari and an SIO2PC or SD device

The simplest route for ordinary, unprotected disks. Connect the Atari to a PC with an SIO2PC cable running RespeQt (or use an SD-card device), keep a real drive as D1:, and mount a new blank image of the right density as D2:. Then copy the real disk to the image with a sector copier on the Atari. Your Atari drive, which reads Atari disks reliably, does the reading, and the PC just stores the result.

Limits: what you get is only what the Atari drive and copier can read, so copy-protected disks won't come out working. For those, see routes C and D.

Route B: an Atari drive connected straight to the PC

A 1050-2-PC cable connects a stock Atari disk drive directly to a PC, with no Atari computer at all. Nick Kennedy designed the original. Commercial versions include Lotharek's 10502PC/SIO2PC-USB, the Atari8Warez SIO2PC/10502PC Dual-USB, and the Atarimax Universal SIO2PC/ProSystem interface. Software that drives them:

  • atarixfer, part of Matthias Reichl's AtariSIO package for Linux, reads and writes ATR images through a 1050-2-PC or ProSystem cable.
  • ALibPc makes ATR archives and writes ATRs back to real disks. It supports the high-speed modes of US Doubler, Speedy and Happy drives.
  • APE ProSystem (Steven Tucker) creates .PRO images, which can also record protected disks, for use with APE.
  • SIO2PC 4.x has a 1050-2-PC function that does direct sector I/O with the drive.

Route C: the PC's own floppy drive

An old PC with a built-in 5.25" drive can read double-density (180K) Atari disks directly. Tools include Matthias Reichl's AtariDsk and WriteAtr for MS-DOS (WriteAtr can create ATR images of DD disks as well as write them), MyUTIL, ATARIO and SpartaRead. Single-density (90K) disks, the 810/1050 format, need a tool that handles the FM encoding: AnaDisk with the DeAna converter, or OmniFlop, have been used for that.

Two traps are worth knowing, from the advice collected in the comp.sys.atari.8bit FAQ. Atari drives spin at 288 rpm rather than the PC's 300, so a PC writing to an Atari-formatted disk can overwrite the next sector's header. Reading is safe, but for writing, format the disk on the PC. And a 1.2 MB high-density PC drive writes a narrower track than a 360K drive, so don't write with one to a disk you want to read in a 360K or Atari drive afterwards.

Route D: flux capture (the preservation standard)

For anything rare, copy-protected or damaged, record the raw magnetic flux rather than decoded sectors. A flux image keeps everything on the track, including the bad sectors, timing and duplicate sectors that protection relies on, so nothing is lost even if the decoder of today can't fully interpret it.

Device Notes
KryoFlux (2009) Developed by the Software Preservation Society. Saves raw stream files and can export Atari XFD. Windows, macOS, Linux.
SuperCard Pro (2013, Jim Drew) Saves .scp flux images and can write back. Its maker notes that "99% of Atari 400/800 commercial disks" were written starting at the index pulse, so it can duplicate them.
Greaseweazle (2019, Keir Fraser) Open-source USB interface, F1, F7 and F7 Plus versions. Produces .scp flux images.
Applesauce (John Keoni Morris) Apple II-oriented, but since version 1.37 (June 2020) it reads FM and MFM disks and can image unprotected Atari DOS 2.0/2.5 disks. macOS.
FC5025 (2010, Device Side Data) Read-only 5.25" controller with Atari 810 support. Cannot handle protected or damaged disks.

All of these connect an ordinary PC 5.25" drive to a modern computer over USB. Avery Lee's a8rawconv then converts the KryoFlux RAW or SuperCard Pro SCP capture into an ATR (unprotected) or ATX (protected) image that emulators and SD devices can use.

Keep the flux files as well as the converted image. They are your master copy. A better decoder can always be run on them later; a disk that has since lost its oxide can't be read again.

Drive enhancements such as the Happy or the Super Archiver can copy many protected disks too, and RespeQt can capture an Archiver copy straight into an ATX. They're fine for personal backups, but flux capture is gentler on fragile originals and more exact.

3. Tapes

Record the tape as audio, in stereo (the Atari's data track on one channel, the audio track on the other), and keep that recording as your master:

  • Use a good deck with Dolby and other processing switched off, and set levels to peak just below maximum.
  • Save as WAV or FLAC, never MP3 or another lossy format, which damages the data, especially turbo formats.
  • Keep the leader at the start.

Then decode a copy to CAS, the standard tape image format. It was invented by Ernest Schreurs for his Digital Cassette Image tools (CAS2SIO, WAV2CAS and CAS2WAV). Tomasz Krasuski's A8CAS extended it to describe the non-standard data that protected tapes use. A CAS holds only the data track, so keep the audio recording too, especially for tapes with a spoken or musical audio track. Loading and Saving Atari Cassettes has the full recording checklist, and Turbo Tape Systems covers the Eastern European fast-loading formats.

4. Cartridges

  • Use a proper dumper. The AtariMax USB Cartridge Programmer, with its PC software, can dump almost any cartridge.
  • Don't hot-plug. Home-made dumpers from the 1980s worked by plugging a cartridge into a running 800. That risks the cartridge and the computer, and XL/XE machines lock up or reboot when the cartridge state changes unless the program takes special precautions. If you must use the Atari itself, a cartridge extender with a switch, so the cartridge stays seated while the machine boots, is the safer way.
  • Record the type. A .ROM (or .BIN) file is a raw dump with no header. A .CAR file, the atari800 format, adds a header with the cartridge type, which emulators need for bank-switched cartridges. When you dump a cartridge with more than 8K or 16K, find out its banking scheme (see Bank-Switched Cartridges: Programming XEGS and Atarimax Carts) and record it.

5. Check what you made

An image you haven't tested is a guess:

  • Boot it in two emulators (Altirra and atari800), and on real hardware through an SD device or FujiNet if you can.
  • Read the disk twice and compare the images. Differences mean a marginal disk or drive.
  • For protected disks, check that the ATX boots and passes its protection in Altirra. If it doesn't, keep the flux and try again with a different drive or decoder settings.
  • Name files clearly: title, publisher or source, side, and the date you imaged it. Keep your notes and photos with the images.

6. Share it

Undumped cartridges and unarchived disks still surface every year, and the people best placed to recognise them are on the AtariAge forums and the catalogue sites such as Atarimania. Before you share, check whether the item is already preserved, and if your copy differs (another version, a prototype, a user group's own disk), say so. Your own programs and your club's newsletters are history too.

Troubleshooting

  • The copy boots but crashes later: the disk is probably protected or has a marginal sector. Re-image with flux capture.
  • The PC drive reads nothing: it may be a single-density disk (route C tools need DD), or a 3.5"/HD drive set up for the wrong format.
  • Errors on a known-good disk: clean the head and check the drive speed before blaming the disk.
  • A tape won't decode: recheck the levels and Dolby settings, try the other channel, and keep the WAV whatever happens.
  • A cartridge image doesn't run: wrong size or banking type. Check the .CAR type, or the raw dump's length.

Further reading

  • Michael Current, comp.sys.atari.8bit FAQ, sections 9.1 (image formats) and 10.1–10.3 (reading Atari disks on a PC).
  • On this site: Atari 8-bit File Formats Explained, Copy Protection and ATX Disk Images, Loading and Saving Atari Cassettes, Turbo Tape Systems, SIO2PC and RespeQt: Using Your PC as an Atari Disk Drive, CARTDUMP: A One-Sector Cartridge Dumper from the 1980s Resurfaces.

Credits