Calling Atari BBSes Today: Modems, Terminals and Emulators

Atari text screen showing ATDI 127.0.0.1 23230, OK, WELCOME TO THE TEST BOARD, ENTER YOUR NAME: and HELLO ATARI! GOODBYE.

Bulletin board systems were the Atari's social network in the 1980s, and many are back, now reached over the Internet instead of a phone line. From the Atari's point of view nothing has changed. Software talks to an R: device, sends Hayes AT commands to a "modem", and gets CONNECT and NO CARRIER back. The modem just happens to open a network connection instead of dialling. That means the original terminal programs still work.

This guide covers the practical side: getting a modem (real or emulated), choosing a terminal program, the settings that trip people up, and a 12-line BASIC terminal that shows how it all works. For the hardware in detail, see the Internet and Wi-Fi Modems for the 8-Bit Atari hardware entry.

1. Two kinds of board

Before you dial, know what's on the other end:

  • ATASCII boards run Atari BBS software (FoReM, BBS Express!, Carina, AMIS and their descendants) or modern systems that speak the Atari's own character set. You see Atari graphics characters, inverse video and colour changes, and the Atari's RETURN code works as is. Use an ATASCII terminal such as BobTerm or 850 Express!, with translation off.
  • ASCII/ANSI boards are PC-style systems, Unix hosts and most of the BBS world. They expect carriage returns and ANSI or VT100 escape codes. Use Ice-T in ANSI or VT102 mode, with translation on, so that RETURN is sent as a carriage return and incoming line endings are converted.

A burst of garbage, or everything on one line, almost always means the wrong choice here.

2. Getting a modem

There are four routes, in rough order of convenience:

Route What you need Notes
FujiNet A FujiNet on the SIO port Emulates an 850 with a Hayes modem. The R: handler loads from the device itself. Dial with ATDT host:port.
850 or P:R: Connection + modem An RS-232 interface, and a Wi-Fi modem or a tcpser box on its serial port The classic setup, as in the 1980s. Load the interface's R: handler at boot.
SIO2PC A PC running APE, or the experimental AspeQt-2k26 fork of RespeQt The PC emulates the interface and modem.
Emulator Altirra or atari800 Nothing to buy. Good for trying boards and for testing.

FujiNet. FujiNet's own test procedure is a good first call. Mount modem-programs.atr from the Atari_8-bit/Comms folder on the atari-apps.irata.online TNFS host as D1:, boot it, and pick 1 for BobTerm. Press B to step the speed to 4800 baud and RETURN for terminal mode. Type AT and RETURN (FujiNet answers OK), then ATDT followed by a board's address, for example ATDT basementbbs.ddns.net:9000. The modem replies CONNECT 4800 and the board's login appears. When you log off, FujiNet says NO CARRIER.

Altirra. Under System, Devices, add an 850 Interface with its modem. Dialling out uses its own syntax, ATDI hostname port, for example ATDI localhost 23. Outbound connections must be enabled in the serial options, or the modem answers NO DIALTONE. Leave the emulation level at None or Minimal for most programs. Altirra then installs its own high-level R: handler, which uses no Atari memory. Full emulation bootstraps a 6502 R: handler from the emulated 850, for programs that need the real thing.

atari800. Start it with -rdevice, and the R: device's modem accepts the same ATDI hostname port command. This is what the BASIC terminal in section 6 was tested with.

3. Choosing a terminal program

  • BobTerm (Bob Puff, 1989–90) is the usual choice for ATASCII boards. It has XMODEM, YMODEM and variants, VT52, a chat window, a capture buffer and a dialling directory. Use version 1.21 or 1.22. Rename the R: handler you need to RS232.COM and BobTerm loads it at start-up.
  • Ice-T (Itay Chamiel, from 1993, with new releases in 2025) is the best client for ANSI boards and Unix shells. It has accurate VT102, a readable 80-column screen, and ZMODEM downloads. The XE version needs 128K. It uses the same RS232.COM handler convention.
  • 850 Express! (Keith Ledbetter, 1986) and AMODEM are the period classics, still worth a look on real 850 setups.

On a FujiNet, modem-programs.atr collects terminal programs ready to boot, so you don't have to assemble a disk yourself.

No Atari to hand? ATASCII boards can also be called from a PC with a terminal that understands the Atari character set. The README of the new Action 8 BBS suggests SyncTERM (Windows, Linux, macOS), MuffinTerm (Mac) and AtConnect (Windows).

4. Settings that matter

Telnet or raw. Many boards accept a plain TCP connection. A server running a real telnet daemon expects option negotiation (IAC codes) first and may not send anything until it gets it. Without telnet support, you see a few odd characters at the start, or a login prompt that never comes. FujiNet's modem has a full telnet parser, switched on with ATNET1. Altirra has a Telnet emulation option on the modem. atari800's R: device sends telnet negotiation codes by itself when it dials.

CR/LF. Telnet sends carriage return plus line feed. ATASCII boards in particular may see the extra line feed as a stray keystroke. Altirra's Automatic CR/LF conversion option fixes that, and turns itself off for the session if it sees an ATASCII end-of-line character, so ATASCII boards stay binary-clean. Don't use it for file transfers on ASCII boards.

Speed. Pick a rate the software and handler can sustain. FujiNet's walkthrough uses 4800 baud. Faster rates need fast serial hardware and a terminal that can keep up: the 850's serial ports top out at 9600 bit/s, and other interfaces at 19,200. Over the Internet, the "baud rate" only limits how fast the Atari is fed.

CONNECT codes. Some BBS-era software expects a particular numeric CONNECT code for higher speeds. Altirra's modem returns the Conexant code for 9600 baud (12), and lets you force a fixed speed into the CONNECT message for software that checks it.

File transfers. XMODEM and its variants work with both kinds of board. Turn translation off before a binary transfer, or the file will be corrupted.

5. What happens when you dial

Every terminal program does the same few things through CIO:

  1. Set translation and parity with XIO 38 (in BASIC). The value 32 means no translation, for ATASCII; 0 means light ASCII translation.
  2. OPEN the R: device for reading and writing.
  3. Start concurrent mode with XIO 40, so data can flow both ways at once with an input buffer.
  4. Send AT commands as ordinary text. The modem answers with text too.
  5. In a loop, use STATUS to see how many characters are waiting (location 747), read them with GET, and send keypresses with PUT.

6. A 12-line terminal in Atari BASIC

10 REM TINY TERMINAL FOR THE R: DEVICE
20 XIO 38,#1,32,0,"R:"
30 OPEN #1,13,0,"R:":OPEN #2,4,0,"K:"
40 XIO 40,#1,13,0,"R:"
50 PRINT #1;"ATDI 127.0.0.1 23230"
100 STATUS #1,A:IF PEEK(747)=0 THEN 200
110 GET #1,C:IF C=13 THEN C=155
120 IF C<>10 THEN PRINT CHR$(C);
130 GOTO 100
200 IF PEEK(764)=255 THEN 100
210 GET #2,K:IF K=155 THEN K=13
220 PUT #1,K:GOTO 100
  • Line 20 turns translation off before the OPEN, as the 850 manual's examples do. The program does its own conversion instead.
  • Line 30 opens R: with 13: read (4) + write (8) + concurrent (1). It also opens the keyboard on channel 2.
  • Line 40 starts concurrent I/O. Note the 13 again. BASIC's XIO stores its first number into the IOCB's AUX1 byte, which also holds the open mode. The first version of this program used XIO 40,#1,0,0 as many listings do, and the next GET failed with ERROR 131 ("IOCB write only"), because the channel no longer claimed to be open for reading.
  • Line 50 dials, here a test server on the same PC, using the ATDI host port syntax of atari800 and Altirra. On a FujiNet, change it to ATDT host:port.
  • Lines 100–130 print whatever has arrived. A carriage return becomes an Atari EOL (155) and line feeds are dropped.
  • Lines 200–220 send keypresses, turning RETURN (155) into a carriage return (13) for ASCII boards. Location 764 is 255 when no key is waiting.

Run in atari800 with -rdevice, it dialled, got OK, showed the test board's prompt and sent back the typed reply, as in the screenshot. Pointed at the Basement BBS on port 9000, it connected and displayed the board's own "busy" message. Atari BASIC is too slow for fast text, so treat this as a learning tool and use a real terminal program for calling.

7. Finding boards

  • The FujiNet wiki's BBS pages link to a list of active Atari BBSes that FujiNet can reach. Its own tests use Southern Amis (southernamis.ddns.net) and the Basement BBS (basementbbs.ddns.net:9000).
  • bbs.fozztexx.com is the FujiNet developers' standard example of a board that implements telnet properly, so turn telnet on (ATNET1) for it.
  • All three accepted connections in November 2026. Boards come and go, so check a current list.

On the two boards in FujiNet's test, new users type NEW (as the password on Southern Amis, as the handle on the Basement BBS), ? at the main prompt lists the commands, and G logs off. Log off properly rather than just hanging up.

Troubleshooting

  • No OK after AT: the R: handler isn't loaded, or the terminal is talking to the wrong device. Check that RS232.COM (or the 850/FujiNet autoload) ran at boot.
  • NO DIALTONE in Altirra: outbound connections are disabled in the serial options.
  • Connects but nothing appears: the host is waiting for telnet negotiation. Turn telnet on (ATNET1 on FujiNet, Telnet emulation in Altirra).
  • Garbage or graphics characters on an ASCII board: turn translation on, or use Ice-T.
  • Everything on one line, or double-spaced: a CR/LF mismatch. Toggle the terminal's line-feed option, or Altirra's CR/LF conversion.
  • ERROR 131 in your own program: an XIO on the open channel changed AUX1. Repeat the open mode (12 or 13) in every XIO's first number.
  • Lost characters at high speed: lower the baud rate. Most Atari software is comfortable at 2400–4800.

Further reading

  • Atari 850 Interface Module Operator's Manual, for XIO 34–40 and the R: device.
  • The comp.sys.atari.8bit FAQ, sections 7.5 (R: and T: handlers) and 7.6 (fast modems).
  • Altirra's help file, "850 Interface Module emulation", for every modem option.
  • On this site: FujiNet Setup Guide, the BobTerm, Ice-T, 850 Express! and AMODEM software entries, Internet and Wi-Fi Modems for the 8-Bit Atari, CIO and IOCBs: How Atari Input/Output Really Works, Running an Atari BBS Today.

Credits