Corvus Disk System for the Atari 800
- Year
- 1982
- Type
- Storage
- Category
- Winchester hard disk system (controller-port interface)
- Manufacturer
- Corvus Systems, with drives from International Memories Inc. (IMI)
- Tags
- hard-disk, winchester, corvus, atari-800, multiplexer, bbs, networking, 1982
- Related
- RealDOS, ADS Integrater, CSS Multiplexer (MUX)
Overview
Before the XL's parallel bus existed, the only way to put a hard disk on an Atari was the Corvus Disk System. Corvus Systems worked with drive maker International Memories Inc. (IMI) to sell integrated Winchester systems for many computers. In 1982 it offered an Atari 800 Disk System in 5, 10 and 20 MB packages. It was the first hard disk solution for an Atari, and for several years the only one. Its interface plugged into the 800's joystick ports 3 and 4, and with Corvus's multiplexers dozens of Ataris could share one drive. That suited large bulletin boards.
Specifications
| Item | Value |
|---|---|
| Introduced | 1982 |
| Drive options | B-Series 5.25" 6 MB, 8" 11 MB, 8" 20 MB; H-Series 5.25" 6/12/18 MB (Models 6, 11, 20) |
| Interface | Corvus Atari Interface on controller jacks 3 and 4, linked to the drive's 34-pin Processor port |
| Daisy chain | Up to 4 drives per computer |
| Requirements | 48 KB RAM and an 810 (or equivalent) drive; boots from a Corvus boot disk or cassette |
| Volumes | SYSGEN divides the drive into 90 KB and 180 KB volumes (a Model 20 holds up to 196 single-size volumes) |
| Software | Two "AT Utilities" disks; WRITEBOOT.OBJ builds a Corvus boot disk from DOS 2.0S ("DOS II Corvus A2.0D") |
| Backup | Corvus Mirror, internal or external, backs up to a VHS or Beta VCR |
How it works
The interface is the clever part. Two joystick ports give only eight usable data lines through the PIA, so the interface works as a nibble-wide link. Port 3 (PORTB bits 0-3) carries data four bits at a time in either direction. Port 4 (bits 4-7) sends control codes: write low nibble, write high nibble and send, receive and read low nibble, read high nibble, read status. Bit 7 strobes each command. The drive itself appears as a linear array of 512-byte blocks that can be read as 128-, 256-, 512- or 1,024-byte sectors.
Because the ports used are 3 and 4, the system is for the 400/800. XL and XE machines have only two joystick ports.
Multi-user setups
Each user boots a personal Corvus boot disk and then loads a "volume mount table" file with DOS's binary-load option. It maps up to eight logical drives to that user's Corvus volumes or real Atari drives. A Corvus Multiplexer configured as a host gives 8 Processor ports, and a master multiplexer can feed eight hosts, so in theory 64 computers can share up to 80 MB. The ADS Integrater personality board for the 800 (1983) added a faster RAM disk and direct Corvus booting.
This wasn't just theory. In May 1988 Antic gave its Outstanding BBS award to CompuTalk of Fort Worth, Texas, which linked six 48K Atari 800s, each with a modem and an 850 interface, "via a 20Mb Corvus Hard Disk and Multiplexer". At the time it took about 230 calls a day.
Using one today
Surviving Corvus systems are rare, and the IMI drives inside are now more than 40 years old. Corvus published its full protocol in Corvus Mass Storage Systems General Technical Information, so the system is well documented for anyone restoring one.
Credits
- Picture: A later Corvus OmniDrive hard disk, shown for the Corvus family. The Atari system used B- and H-series drives. — HabderdashersSon, via Wikimedia Commons (CC BY-SA 4.0)
- comp.sys.atari.8bit FAQ (Michael Current), section 3.3.1 What is the Corvus disk system? — Michael Current (comp.sys.atari.8bit FAQ)
- Altirra Hardware Reference Manual, section 7.11 Corvus Disk System — Avery Lee (Altirra)
- Antic Vol. 7 No. 1 (May 1988), Antic Awards: CompuTalk Outstanding BBS — AtariMagazines.com (Kevin Savetz), 1988
