From Protoboard to Rev6: How FujiNet's Hardware Took Shape, 2019–2020
FujiNet is now the most popular way to put an 8-bit Atari on the network. Its first year of hardware happened in a series of small batches of hand-built boards, and the project's wiki keeps a record of each one. Read in order, the revisions show how a Wi-Fi experiment hanging off a serial cable became a self-contained SIO peripheral. Almost all the boards were designed by mozzwald, with one by a8bit.
NodeMCU on top: Rev0 to Rev3 (2019)
- Rev0: protoboard. Parts were wire-jumpered on perfboard, with an off-the-shelf NodeMCU 1.0 Wi-Fi module on top and an SIO cable on header pins. It was meant to draw power from SIO, but the cable broke easily. Thom retired his when the Rev2 boards arrived.
- Rev1 (29 October 2019). The first proper PCB, three made, with surface-mount parts and the first try at a surface-mount SIO connector built into the board. The case was never finished, so the boards shipped with a 3D-printed bracket to hold the connector. They were powered over USB, or from SIO with a solder jumper. The Rev1 board's silkscreen still reads "SIO2WiFi Modem". Rev1 saw heavy use during early firmware development.
- Rev2 (16 November 2019). Three more boards. These added a two-pin serial debug port, a slide switch for SIO power, the SIO clock lines (CLOCKIN fitted and CLOCKOUT optional) and a two-transistor buffer on DATAIN, a design credited to jeffpiep.
- Rev3, "the Mars Bar". a8bit's design, a batch of ten, with a better-chamfered SMD SIO connector, SIO or USB power and a pass-through SIO socket for other devices. Like Rev1, some were still in use when the wiki page was written.
The ESP32 arrives: Rev4 to Rev6 (December 2019 – April 2020)
- Rev4, "the Ice Cream Sandwich" (6 December 2019). The first ESP32-based PCB, ten made. No NodeMCU was needed, because the board itself carried an SIO plug and receptacle, micro-USB with a CP2102 USB-serial bridge for power and programming, a microSD socket, flash and reset buttons, and two LEDs (blue for Wi-Fi, orange for SIO activity).
- Rev5, "the FrankenFuji" (5 April 2020). The first vertical design, standing up behind the computer. A pin-out mistake on the SIO connectors meant only the socket could be fitted. It worked, but only one was built.
- Rev6 (14 April 2020). The vertical layout done properly, ten made for developers and testers. It was the first to use the ESP32-WROVER module with 16 MB flash and 8 MB PSRAM, the combination later production boards kept. It added a third button and a Bluetooth LED, kept the pass-through SIO plug and receptacle, added an optional JTAG port, and came with XL-style or XE-style 3D-printed cases. A PCB mistake still needed a trace cut and bodge wires.
On to production
Rev6 led straight into the numbered boards. The first official design, FujiNet 1.0, kept the Rev6 essentials: a custom SIO plug that goes straight into the computer, a receptacle on the back, the WROVER module, microSD, three buttons and three LEDs (white for Wi-Fi, blue for SIO2BT, orange for SIO). Two more prototype rounds followed. v1.1 added line buffers on SIO DATAIN and DATAOUT so FujiNet would work on the 1088XEL, which has SIO2PC built in, and added a safe-reset button. v1.2 put the SIO lines behind two 74LS07 buffers that are disabled when the power switch is off, made the switch control the 3.3 V regulator, and added a pull-down on MOTOR CONTROL for cassette emulation. Those changes became production version 1.3. Versions 1.5, 1.6 and 1.7 then fixed a firmware-flashing fault, added ESD protection and an SD card-detect line, and replaced micro-USB with USB-C. The hardware designs are published in the project's fujinet-hardware repository.
Why it matters
For owners today, the history explains a few details of the device: why it is shaped the way it is, why it has a pass-through port, and why some early units need the hardware fix documented for 1.3 boards. It also shows a typical open-hardware project at work. Each batch of three or ten boards went to the people writing the firmware, and every mistake (a mirrored pin-out, a missing buffer, a bodge wire) was written down and fixed in the next run.
Credits
- Picture: The Rev6 vertical prototype in its XL-style and XE-style 3D-printed cases. — Photo from the FujiNet project wiki (Prototype Board Revisions page), FujiNetWIFI.github.io repository
- FujiNet wiki — Prototype-Board-Revisions — FujiNet project
- FujiNet GitHub wiki — Prototype-Board-Revisions (markdown source with image links) — Photo from the FujiNet project wiki (Prototype Board Revisions page), FujiNetWIFI.github.io repository
- FujiNet wiki — Official-Hardware-Versions — FujiNet project
