SIO2IDE
- Year
- 2002
- Type
- DIY project
- Category
- SIO hard disk / CF / CD-ROM interface
- Manufacturer
- MMSoft (Marek Mikołajewski), Gdańsk; later builds sold by Mega-Hz
Overview
SIO2IDE takes the opposite approach to parallel-bus hard disks like MyIDE or the KMK/JŻ IDE. Instead of wiring a drive onto the computer's bus, it puts a microcontroller between an IDE drive and the SIO port. To the Atari it looks like a stack of ordinary floppy drives, so it works with any OS, any DOS and any model from the 800 to the 130XE. Other SIO devices can share the chain, including a second SIO2IDE set as slave.
The clever part is on the disk side. SIO2IDE reads a PC-formatted FAT16 or FAT32 disk and serves .ATR image files from it. You prepare the disk on a PC by copying ATRs and a small text config file, then plug it into the Atari. From version 3.0 it also reads ISO9660 CD-ROMs through ATAPI.
The designer was Marek Mikołajewski (MMSoft) of Gdańsk, Poland. Development ran from 2001 to 2005; version 3.0 is dated March 2002. Later 4.x versions added a USB mode that exposes the disk to a Windows PC as a mass-storage device. Wolfram Fischer (Mega-Hz) offered a version 3.3 build.
Hardware
| Item | Detail |
|---|---|
| Microcontroller | Atmel ATmega161-8 (16 KB flash, 1 KB RAM), 7.3728 MHz crystal |
| Other parts | 10 µF and 2 × 30 pF capacitors, 4 × 330 Ω LED resistors, 4.7 kΩ, IDC40 IDE header, 3 jumpers |
| LEDs | PWR, SIO (command received), BSY (busy/error), IDE (bus activity) |
| Jumpers | HD1_ZW (D1: on/off), INIT_ZW (swap D1:/D2:), MS_ZW (master/slave interface) |
| IDE | full 16-bit, CHS and LBA, ATA disks, CF cards, ATAPI CD-ROM |
| SIO | 19,200 bit/s standard; later firmware added US Doubler/Happy high speed (~52 kbit/s) |
| Drives emulated | D1:–D7: in v3.0 (reduced from 8 in v2.1 to free space for new features) |
| ISP header | 8-pin in-system programming connector for firmware updates |
SIO wiring (SIO2IDE connector → Atari SIO): pin 1 → SIO 5 (computer Data Out), pin 2 → SIO 3 (computer Data In), pin 3 → SIO 7 (Command), pins 5/6 → SIO 4 (GND), pin 7 → SIO 10 (+5 V). Pin 4 is a Reset_Out line that is held low during start-up while D1: is enabled.
A 2.5" laptop drive is recommended because it runs from +5 V alone and draws little power. That makes an internal installation practical. A 44-to-40-pin adapter connects it to the IDE header.
Preparing the disk
- Partition and format the drive under DOS or Windows 9x. Only the primary partition is used. Supported types are $04 and $06 (FAT16), $0C (FAT32 LBA), and ISO9660 for CDs.
- Copy your
.ATRimages. Each must have a valid 16-byte header and be defragmented (the interface ignores fragmented files). Rundefrag.exeafter copying. - Put a
SIO2IDE.CFGtext file (512 bytes max) in each folder you want to use. Lines look likeD1=MDOS453, with the drive number 1–7 and the ATR name without extension, in capitals, starting in column 1. - On power-up the interface always starts from the root folder. Use FDISK.COM on the Atari to change folders, browse ATRs, assign images to drives, mark them read-only and save the config. Choose Master or Slave first if you have two interfaces.
The PC utilities CHECKFS.EXE (checks a disk's layout; it doesn't work through USB-attached drives) and MAKEATR.EXE (creates blank ATRs, which you then format in an emulator) complete the kit. The AVR is programmed from the supplied SIO2IDE.HEX with AVRPGR.
Pitfalls
- Long filenames aren't supported. Use 8.3 names on FAT, and LFN-only files on CDs are invisible.
- An ATR stored in a folder without a config file can't be used.
- Fragmented images simply don't appear, so re-run defrag whenever you add files.
- ATAPI CD-ROMs are read-only, so the read-only/read-write toggle doesn't apply to them.
Using it today
SIO2IDE was soon overtaken by SD-card devices such as SIO2SD and SDrive, which follow the same principle with smaller media. But it pioneered the idea of serving ATR files from a PC filesystem over SIO, and CompactFlash cards in a CF-to-IDE adapter make it a quiet, practical build even now. SpartaDOS X users can drive it with DLT's S2I add-on.
Credits
- Picture: An SIO2IDE 4.x controller board, photographed by its designer Marek Mikołajewski (MMSoft). — its designer Marek Mikołajewski(MMSoft), from the 'MMSoft's SIO2IDE' page hosted by atari.area (atariarea.krap.pl) (Used for identification/commentary)
- SIO2IDE v3.0 Technical Specification (MMSoft, 2002; Nir Dary collection) — Nir Dary collection, 2002
- SIO2IDE v3.0 Users Manual (MMSoft, 2002) — MMSoft, 2002
- SIO2IDE 3.0 bill of materials
- SIO2IDE readme / version history (Polish) — Polish
- comp.sys.atari.8bit FAQ, section 3.3.4 (Michael Current, Feb 2026) — Michael Current (comp.sys.atari.8bit FAQ), 2026
