Atari in a PC Case (and the TransKey Keyboard Board)

Year
1990
Type
DIY project
Category
Case conversion / system build
Manufacturer
Homebrew project (instructions by Micro Solutions; posted by Frank E. Seipel, 1990)
Atari 130XE with disk drive, program recorder, printer, touch tablet and joystick spread across a desk

Overview

By 1990, PC-style cases with switching power supplies, drive bays and detachable keyboards were cheap and everywhere. Micro Solutions published a public-domain guide, posted to the Info-Atari8 digest by Frank E. Seipel in December 1990, for moving an Atari 8-bit into an IBM-style case together with its drives and a hard disk. Micro Solutions made the TransKey board, which lets an IBM keyboard drive the Atari, and the guide naturally recommends it. The guide assumes a thorough grasp of basic circuits, soldering and some mechanical skill, and it is a framework rather than a step-by-step manual.

Choosing the computer

An 800XL, 600XL or XE is strongly preferred:

  • They need only +5 V, which the PC supply provides in quantity. The 400/800 and 1200XL want 9 V AC, or +5, +12 and −5 V DC if bypassed, and PC supplies don't offer −5 V or 9 V AC.
  • They have the parallel bus (PBI/ECI) for a fast hard-disk interface, plus built-in BASIC.

Power plug: XL/XE machines use a 7-pin DIN (an 8-pin DIN works with its centre pin removed). Pins 1, 4 and 6 are +5 V and 2, 3, 5 and 7 are ground. Make a pigtail from a 4-pin floppy power plug to a DIN plug.

Floppy drives: XF551 controllers

The XF551's mechanism is a standard PC 5.25" drive, so its controller board can be reused:

  1. Remove the drive and controller from the XF551 case.
  2. Replace the controller's soldered 34-pin cable header with a male IDC header, and the 4-pin power lead with a PC floppy power connector (pin 1 = +12 V, 2 and 3 = GND, 4 = +5 V).
  3. Connect a standard PC floppy cable, using the end connector, and power both board and drive from the PC supply. Set the SIO drive number on the controller's switches.

This gives 360 KB per disk under MyDOS or SpartaDOS. A 3.5" PC drive can replace the 5.25" one on the same controller, also at 360 KB. For full 720 KB, the guide points to Innovative Concepts' 3.5" kit.

Dual media from one controller: cut the trace between pins 10 and 16 of the 34-pin header (leaving pin 16's other trace intact), then wire an SPDT switch with pin 16 to the common and pins 10 and 12 to the two sides. The switch selects either the 5.25" drive (end connector) or the 3.5" drive (middle connector). Only one is usable at a time, so a second controller is needed for drive-to-drive copying.

Hard disk

For a fast hard disk, use a parallel-bus SASI/SCSI host adapter: the CSS Black Box, ICD MIO or Supra interface. The author used a Black Box with an 800XL and extended its bus with a crimp-on cable (a 50-pin edge connector, a 50-pin IDC plug and about 12" of ribbon), with no soldering. Always line up pin 1 at both ends. The SIO-connected ATR8000 is a slower option suitable for 400/800 users.

Power-on delay

Hard disks need a few seconds to spin up, and booting too early causes errors. The author's fix was a 555 timer driving a 5 V relay in series with the computer's power line. At switch-on the timer output is high and the relay stays open. When the RC delay expires, the output drops, the relay closes and the Atari powers up. A separate front-panel switch for the computer does the same job by hand.

TransKey

TransKey is a microprocessor-based translator board, about 2.5 × 3.5 inches, that fits under the RF shield (on a 1200XL, the shield must be cut or left out). It lets a standard IBM-style keyboard drive the Atari, and it works with the 400, 800, XL and XE. Thanks to the extra function and cursor keys, it adds features the original keyboard couldn't, such as sending whole BASIC or MAC/65 commands with one keypress. For a later DIY equivalent, see AKI.

Practical tips

  • You'll need lots of spacers, standoffs and card guides. Boards can stand on end or be stacked.
  • Use floppy-power Y-adapters when you run out of connectors.
  • Keep the RF shielding where possible, and route ribbon cables away from the switching supply.

Credits

  • Picture: A typical XE setup of separate boxes and cables, the clutter a PC-case conversion consolidates. — Terry Ross, Wikimedia Commons (CC BY-SA 2.0)
  • Micro Solutions — ATARI-->PC Conversion (posted by Frank E. Seipel to Info-Atari8, 8 Dec 1990), Nir Dary collection — Micro Solutions, 1990
  • Frank E. Seipel — Transkey: IBM keyboard on an 8-bit, hardware review (Info-Atari8, 5 Nov 1990) — Frank E. Seipel, 1990