APE Warp+ OS 32-in-1

Year
2005
Type
Modern device
Category
Switchless multi-OS upgrade module (XL/XE)
Manufacturer
Atarimax (Steven J. Tucker)
Small green APE Warp+ OS circuit board with a PLCC flash chip socket, a controller chip and a four-pin header

Overview

The APE Warp+ OS is a replacement operating system for Atari XL and XE computers from Atarimax (Steven J. Tucker). It was built around Atarimax's APE (Atari Peripheral Emulator) PC software and its Warp+ 3x high-speed SIO mode. Because the fast SIO code lives in the OS ROM itself, everything loads at high speed, including games and disk images that would knock out a software patch or a special DOS. From 1996 to 2005 it shipped on the Quad OS module, with four OS images and two toggle switches. From 2005 it came as the APE Warp+ OS 32-in-1, a "switchless" module with 512 KB of flash holding 32 OS images, chosen from an on-screen menu.

Specifications

Item Value
Maker Atarimax (Steven J. Tucker)
Versions Quad OS module (1996-2005, 4 OSes, 2 switches); 32-in-1 module (2005 on, switchless)
Flash 4 Mbit (512 KB) = 32 slots of 16 KB; original chip an AM29F040B in a PLCC socket
Fits XL/XE OS ROM socket; all XL/XE models except the XEGS. The 1200XL kit adds an XE MMU and internal BASIC upgrade
Extra connections SELECT key, PIA port B bit 7 and the reset line (three wires)
Menu Slot 31; Select+Reset, or SELECT held at power-up
Included OSes APE Warp+ OS, standard XL/XE OS, XL/XE OS with reversed BASIC, a public-domain 800-compatible OS, MyIDE "I" and "E" OS ROMs, and others
Price $49.99 self-install kit, $79.99 with professional installation (Atarimax)

Features of the Warp+ OS

  • Warp+ 3x SIO with APE on a PC, built into the OS so it's always active. Atarimax's benchmarks show games like Alternate Reality: The City, The Pawn and Agent USA loading in roughly a third of the time they take from a 1050. That's an average speed-up of about 320%.
  • UltraSpeed compatibility with US Doubler-style drives, including disks formatted with UltraSpeed skew. Enhanced and plain drives can be mixed on the SIO chain, and the OS switches between them.
  • US Doubler emulation and other power-user touches.
  • Cold start on demand: hold SELECT and press RESET for a full cold boot without touching the power switch.
  • Reverse BASIC: BASIC is off by default, and holding OPTION turns it on.
  • APE Remote Control: hold SELECT+OPTION at power-up.

How it works

The module plugs into the OS ROM socket. Through that socket it sees address lines A0-A13 and the data bus, but not A14, A15 or the read/write line. So it can only map flash into the OS and self-test address windows: each 16 KB slot fills $C000-$CFFF, the self-test area at $5000-$57FF, and $D800-$FFFF, just like a stock XL OS.

Slot selection is stored in non-volatile memory. On power-up the computer boots straight into the chosen OS without a pre-boot BIOS, so the selected OS behaves exactly like a real ROM. The menu is just another OS image, in the last slot ($1F). Holding SELECT forces it to load, and SELECT is sensed in hardware, so software can't block it.

To change slots, the menu talks to the module over the PIA port B bit 7 line (the self-test enable bit), sending a slow (about 1,100 baud) serial stream. Commands and replies are three-byte packets. $55 XX XX selects slot XX, after which the module resets the computer into the new OS. $55 20 20 asks for the current slot, and the module replies $AA YY YY. The module can drive the reset and PB7 lines itself.

Because it can't see writes or decode the full address range, the 32-in-1 can't reprogram its own flash from the Atari. To change the OS line-up you remove the flash chip and program it externally. Atarimax provides an APE Warp+ OS Builder tool to make custom 512 KB images.

Using it today

  • Installation. The module goes into the OS socket. On machines with a soldered OS you have to remove the chip and fit a 28-pin socket first. Three extra wires go to the SELECT key, PB7 and reset. Atarimax published guides for the 130XE, 800XL, 65XE and 1200XL.
  • Custom line-ups. Owners rebuild the image with the OS Builder and burn it with a flash programmer such as a TL866. Use a 5 V 29F040-class part: some replacement chips, including 3.3 V parts sold under similar numbers, have caused erratic behaviour.
  • 1200XL OS images in a slot lack internal BASIC and PBI support, so they aren't a full stand-in for a stock XL OS.
  • Emulation. Altirra emulates the APE Warp+ OS 32-in-1 device, and its hardware manual documents the slot protocol.

Compatibility

  • Works with any SIO devices. High speed applies to APE (Warp+) and UltraSpeed drives.
  • The "800-compatible" slot covers most 400/800-only software, and the stock XL/XE slot covers software that needs Atari's exact ROM.
  • Unlike the Ultimate 1MB it adds no memory, BASIC switching hardware or PBI BIOS. It's purely an OS switcher, which also makes it simple and very compatible.

Credits