Evie FPGA Sound Board

Year
2014
Type
Modern device
Category
Internal FPGA sound expansion (dual POKEY, SID, PSG, Covox)
Manufacturer
Michał "Pasiu" Pasiecznik (SSG), Poland
Green Evie board marked Evie, with a Xilinx Spartan FPGA and an original POKEY chip seated on it, installed on an Atari motherboard

Overview

Evie is a sound expansion for the Atari XL/XE designed by Michał "Pasiu" Pasiecznik of the Polish group SSG and unveiled in May 2014. It's a small board with a Xilinx Spartan FPGA that fits inside the computer. As the photo shows, it sits in the POKEY's place and carries the original POKEY chip on top of it. In the FPGA Pasiu packed nearly every sound chip the 8-bit scene had wanted:

  • emulation of both POKEYs for stereo (dual-POKEY) music;
  • a SID (Commodore 64 sound chip) with selectable filter models;
  • a PSG, specifically the Yamaha YM2149 (the AY-3-8910 family used in the ZX Spectrum 128 and Atari ST);
  • a four-channel Covox 8-bit DAC;
  • the GTIA "buzzer" (console speaker) routed into the stereo mix;
  • a PS/2 keyboard interface.

Sound comes out on its own 3.5 mm stereo jack rather than through the Atari's audio path. Only three prototypes were built, and the design was left waiting for a manufacturer, so Evie is better known through recordings and software support than as a product you could buy.

Specifications

Item Value
Designer Michał "Pasiu" Pasiecznik (SSG), May 2014
Logic Xilinx Spartan FPGA
Built 3 prototypes
POKEY Two (left $D200-$D20F, right $D210-$D21F)
SID $D2C0-$D2DF (optionally also $D500-$D51F); fixed 0.960 MHz clock; filter off, linear (30 Hz-12 kHz), 6581 or 8580
PSG (YM2149) $D2E0-$D2EF, register/data ports $D2F0/$D2F1; clock 1.773 or 1.92 MHz, optionally halved
Covox 4 channels, write-only at $D700-$D703 (or $D600 page, chosen at assembly)
ID / config "Evie" in ASCII at $D2FA-$D2FD, version in BCD at $D2FE, configuration at $D2FF
Output 3.5 mm stereo jack; PSG, SID and buzzer mixed to both channels
Extras PS/2 keyboard with software-controlled Caps/Num/Scroll Lock LEDs

How it works

All the extra chips appear in the POKEY's address page, $D2xx, which the stock Atari only partly decodes. The second POKEY sits at $D210, the usual stereo-POKEY address, so dual-POKEY music players work unchanged. The configuration register at $D2FF controls:

Bit Function
7 Also map SID registers at $D500-$D51F
6-4 PS/2 keyboard Caps, Num and Scroll Lock LEDs
3 PSG clock: 0 = 1.77 MHz (the Atari clock), 1 = 1.92 MHz
2 Divide the PSG clock by two
1-0 SID filter: none, linear, 6581 ("old SID"), 8580 ("new SID")

Software can detect Evie by reading "Evie" at $D2FA and the version byte at $D2FE ($10 means 1.0). Two Covox addresses write the same sample to channels 1 and 2 at once, for simple mono playback. Because decoding isn't complete, the Evie registers also appear at $D280-$D2BF, the SID mirror at $D540, and the Covox at $D740.

Software

  • SID Hardware Player by Mono/Tristesse (SpartaDOS X), for .SID files;
  • PSG Hardware Player by Mono, for .PSG music;
  • Let's Emu!, Konrad Kokoszkiewicz's ZX Spectrum emulator, which plays Spectrum AY music through the PSG;
  • SlightSID Player by xxl;
  • any stereo-POKEY or Covox-aware program, such as trackers and demos.

Recordings of Evie playing the C64 tune from Flimbo's Quest and a PSG piece by Yerzmyey were published by the developers for comparison with a real 8580 SID.

Using it today

Evie never went into series production, but it showed early on how far an FPGA inside the Atari could go, and its players still document how to drive it. If you want similar capabilities in a product you can buy, look at PokeyMAX (pin-compatible POKEY replacement with dual POKEY, SID, PSG and Covox modes in later versions), SUBCART and the ShamaXL AME.

Compatibility

Designed for Atari XL/XE computers (internal fitting). It's compatible with stereo-POKEY software at $D210, SID software at $D500 and Covox software at $D600 or $D700, depending on how the board was assembled.

Credits